Helipad steel structure design services cover the landing deck and the steel frame that lifts it above a roof, whether on a new tower, an existing building or a hospital. Wrenze Steel provides helipad structural design in steel for real estate developers, engineering consultancies and contractors in Dubai and across the UAE, working alongside the aviation consultant who sets the helipad layout and the design helicopter. Our scope is the steel structure: the deck support, the frame, the connections and the tie-in to the building below.
Scope of our helipad steel structure design services
A rooftop helipad design in steel usually covers:
- The deck structure: primary and secondary steel beams under the landing area, sized for the deck system chosen, whether steel plate, a concrete slab on steel beams or proprietary deck panels
- The support frame: columns, bracing and transfer beams that carry the deck above the roof, plant and parapets
- The perimeter: cantilever brackets for the safety net, walkways and access stairs
- Connections and base plates: bolted and welded joints in the frame and the anchorage into the concrete or steel structure below
- The tie-in to the building: support reactions for the building engineer, or a check of the existing structure where the helipad is added later
The aviation consultant sets the geometry: the size of the touchdown and lift-off area, the final approach and take-off area, obstacle limits and markings. We design the steel to suit that layout rather than the other way round, so the frame stays clear of the approach paths.
Helipad structural design in Dubai: landing loads and impact factors
Steel helideck design starts from the design helicopter, normally the heaviest type expected to use the deck, defined by its maximum take-off mass, its undercarriage layout and its overall size. We follow the approach set out in the ICAO Heliport Manual, adjusted to the project specification and the authority’s requirements. The load cases typically include:
- Normal and emergency landing: the touchdown load taken as a multiple of the maximum take-off mass, commonly 2.5 times for the emergency case, applied over the contact area of each wheel or skid
- Sympathetic response: a further factor on the landing load that allows for the dynamic response of the deck structure
- Helicopter at rest: the parked helicopter placed anywhere on the deck, with any equipment and people around it
- General imposed load: a uniform load over the deck for people, maintenance and equipment, as set by the specification
- Horizontal loads: braking and landing loads acting along the deck surface, which the bracing must carry to the supports
Each load is placed at the position that produces the worst effect on each member, so the deck beams are checked for the wheel or skid at midspan, near the supports and at the cantilever edges. The values and factors vary between standards and authorities, so we confirm them with the aviation consultant before starting the design.
Wind, vibration and the perimeter
A helipad sits at the highest and most exposed point of the building. Wind acts on the deck from above and below, and an open frame under the deck can see significant uplift. We design the frame and its connections for the design wind speed of the site, with wind pressures to ASCE 7, BS EN 1991-1-4 or the local requirement named in the specification, and check the deck for load reversal.
Vibration is checked as well as strength. A deck that is too flexible can respond to the helicopter’s rotor and to touchdown, so we check the natural frequencies of the deck and its frame and, where the specification asks for it, keep them clear of the rotor excitation frequencies. Stiffness of the support frame also limits sway, which matters for the deck surface and the fixings of the safety net.
The perimeter safety net is fixed to steel brackets cantilevered from the deck edge. We design the brackets and their connections for the net loads given by the net supplier or the specification. Drainage outlets, fuel and fire-fighting points, lighting and markings are coordinated with the aviation, fire and MEP consultants: we allow for their weights and openings in the steel, while their design stays with those consultants.
Tie-in to an existing roof
When a helipad structure is added to an existing building, the structure below decides what is possible. We review the existing drawings, check the roof slab, beams, columns or core walls that will carry the new loads, and place the support columns over the strongest elements. Where the existing structure cannot take the loads, we design the strengthening as part of a steel structure assessment. Anchorage into existing concrete is designed with the anchor supplier’s data and the edge distances available on site.
What our helipad steel structure design consultants deliver
- A design basis agreed with the aviation consultant: design helicopter, load cases, codes and limits
- Structural calculations for the deck, frame, bracing and safety net brackets, with the vibration check
- Connection designs for the frame joints, base plates and anchorage
- Design drawings: deck framing plan, support frame elevations, sections and typical details
- Support reactions for the building engineer, or the assessment and strengthening design of the existing structure
- Responses to consultant and authority comments on the steel design
How a project runs
- You send the architectural drawings, the aviation consultant’s layout and design helicopter, and the drawings of the building below.
- We agree the design basis, the scope, the programme and the fee.
- We model the deck and frame, run the landing, wind and vibration cases, and size the members.
- We design the connections and the tie-in, and issue calculations and drawings for review.
- We answer the comments, and our team can prepare the shop drawings for fabrication.
Helipads are often designed together with other rooftop steel, such as tower crowns, on high-rise towers.
About Wrenze Steel
- Our engineers hold Dubai Municipality practice certificates, and we prepare Dubai Municipality submissions through to approval.
- A steel structure design consultancy: rooftop and special steel structures are part of our everyday work.
- 96 projects completed across the UAE and the GCC.
- Our office is in Dubai Silicon Oasis, and we work across the UAE and the GCC.
Related pages
Tower crown steel structures · High-rise tower steel · Steel connection design · Steel structure assessment · All steel structure types
For a helipad steel structure design, contact our engineers.

