Steel hangar design company in Dubai and the UAE

Structural steel design of aircraft and equipment hangars: clear-span roof frames, the door girder over the opening, hangar door loads, wind with the doors open, and cranes and services hung from the roof.

Render of the United Airlines facility center in Florida: a large white industrial building with blue trim and a United sign, trucks at the loading bays and a car park in front

Steel hangar design services centre on one thing above all: a large, column-free space with one side that opens almost completely. Wrenze Steel provides structural steel design for aircraft hangars, maintenance hangars and large equipment sheds in Dubai and across the UAE, for real estate developers, architects and engineering consultancies, contractors and steel fabricators. We design the roof frames, the door girder, the bracing, the connections and the base plates, and we coordinate with the door supplier and the aviation consultant so the structure suits the aircraft and the doors.

Scope of our steel hangar design services

An aircraft hangar steel structure usually includes:

  • Main roof frames: portal frames, trusses or space frames spanning the full width of the hangar floor
  • The door girder: a deep truss or girder spanning the full door opening, carrying the roof edge and the top of the doors
  • End posts and door guides: the columns at each side of the opening and the steel that guides or supports the doors
  • Bracing: roof and wall bracing that keeps the building stable with one side open
  • Crane and hoist supports: runway beams for overhead cranes, monorails and points for suspended equipment
  • Annex buildings: workshops, stores and offices along the sides or the back, often with mezzanine floors
  • Connections and base plates: the joints in the frames, splices for transport, and the anchorage into the foundations

The layout comes first. The aircraft size, the clearances around it, the door opening and the roof height set the clear span and the eaves height. From there we choose the frame type and spacing that carry the roof over that large clear span with the lowest practical steel weight.

Hangar door loads and the door girder

The door girder is the most important member in most hangars. It spans the full door opening with no intermediate support and has to stay stiff enough for the doors to operate. Hangar door loads reach it in different ways depending on the door type:

  • Bottom-rolling doors stand on rails in the floor. The top of each door leaf runs in a guide on the girder, so the girder carries the horizontal wind load on the closed doors and the guide loads.
  • Top-hung doors hang from a track on the girder, which then carries their weight as well as the horizontal loads.

The door supplier gives the loads, their positions and the deflection limits the doors can tolerate. These limits often govern the girder design over strength, because a girder that deflects too much under roof load or wind can jam the doors. We design the girder for both, and check its deflection relative to the floor rails as well as its absolute deflection.

Wind, cranes and other design loads

Wind is the main lateral load on a UAE hangar, and the open door case needs care. With the doors open, the opening becomes a dominant opening, and the internal pressure can add to the external uplift on the roof and the pressure on the back wall. We check the structure with the doors open and closed, with wind pressures to ASCE 7, BS EN 1991-1-4 or the local requirement named in the specification.

Other loads include:

  • Roof dead and imposed loads, including roof sheeting, insulation and solar panels where fitted
  • Services: fire suppression pipework, lighting and ventilation ducts hung from the roof
  • Cranes and hoists: wheel loads, impact and lateral surge for overhead cranes on crane runway beams, and loads from monorails and maintenance docks
  • Temperature: long roofs expand and contract with the UAE’s temperature range, so movement joints or sliding bearings are placed where needed

Each frame is checked at the ultimate limit state for strength and stability, and at the serviceability limit state for deflection and sway, so the cladding, the doors and any crane rails work as intended.

PEB hangar vs truss hangar

There are two common ways to build a hangar roof in steel.

A PEB hangar uses tapered portal frames built up from steel plate, with cold-formed purlins and girts. It is economical for moderate spans and repetitive bays, and quick to fabricate. See our PEB steel structure design page for how these frames work.

A truss hangar uses steel roof trusses or space frames for the main roof and a deep truss for the door girder. Trusses suit larger spans and heavier suspended loads, because their depth gives stiffness for less steel weight. The trade-off is more members and more connections to fabricate and erect.

Many hangars combine both: a truss door girder with portal frames behind it, or trusses over the hangar floor with a PEB annex. We compare the options for your span, height and loads before the design is fixed. Our page on long-span steel roof design covers the wider range of roof systems.

What our steel hangar design consultants deliver

  • A design basis covering the aircraft, the clearances, the door type and the loads
  • Structural calculations for the roof frames, door girder, bracing, crane beams and annex structures
  • Connection designs for the frame joints, splices and base plates
  • Design drawings: framing plans, frame elevations, door girder details and typical connections
  • Support reactions and anchor bolt layouts for the foundation designer, including the door rail loads where relevant
  • Calculations and drawings for authority approval, with responses to comments

How a hangar project runs

  1. You send the architectural layout, the aircraft or equipment data, the door supplier’s information and the specification.
  2. We agree the scope, the programme and the fee.
  3. We propose the frame system, with a PEB and truss comparison when useful.
  4. We complete the analysis, member design and connection design.
  5. We issue the calculations and drawings for review and answer the comments.

Aviation and industrial projects

For aviation clients, Wrenze Steel provided engineering services for the United Airlines facility center in Florida, USA, working with the airline’s own engineering division as the consultant and to the airline’s in-house standards, design criteria and review process. More industrial work is on our industrial and warehouse sector page.

About Wrenze Steel

  • Our engineers hold Dubai Municipality practice certificates, and we prepare Dubai Municipality submissions through to approval.
  • A steel structure design consultancy: large clear-span roofs and industrial buildings are part of our everyday work.
  • 96 projects completed across the UAE and the GCC.
  • Our office is in Dubai Silicon Oasis, and we work across the UAE and the GCC.

PEB steel structure design · Steel roof truss design · Long-span steel roof design · Crane runway beam design · All steel structure types

For a steel hangar design, contact our engineers.

Steel hangars: questions

What governs steel hangar design?

Usually three things: the clear span and height needed for the aircraft, the door girder that spans the full door opening, and wind with the doors open, which can raise the internal pressure on the roof and walls. Crane, hoist and services loads hung from the roof are added on top.

How are hangar door loads taken into the structure?

It depends on the door type. Bottom-rolling doors stand on floor rails and need horizontal guidance at the top, so the door girder carries wind on the closed doors and guide loads. Top-hung doors hang from the girder and add vertical load as well. We take the door loads, positions and deflection limits from the door supplier.

Is a PEB hangar or a truss hangar better?

Neither in general. A pre-engineered tapered frame is economical for moderate spans and repetitive bays. Trusses or space frames suit larger spans, heavy suspended loads and deep door girders. We compare the options for your span, height and loads before the design is fixed.

Can you design a hangar for a specific aircraft?

Yes. We start from the aircraft dimensions and the clearances set by the operator or the aviation consultant, and set the clear span, the door opening and the roof height from them. Any future, larger aircraft can be allowed for in the same design basis.

How do you design for the hangar doors?

We design the steel structure that carries and guides the doors: the door girder, the end posts and the guides, using the loads and movement limits from the door manufacturer, who designs and supplies the doors themselves.

How do I choose a steel hangar design company in Dubai?

Look for a steel design company that designs the clear-span frames, the door girder and the bracing for the door loads, wind with the doors open and any cranes or suspended equipment. The design should follow AISC 360, ACI 318 and ASCE 7-16, together with the requirements of Dubai Municipality or the municipality of the project's emirate, with calculations, design drawings and support reactions as deliverables. To start, we need the aircraft or equipment dimensions, the door type and supplier data, and the site layout.